Notifications
Clear all

BEST Subwoofer for under $100? Will Shake your House! ISO 100 Build - MEGA QUAKE


123Toid
(@123toid)
Illustrious Member Admin
Joined: 3 years ago
Posts: 1292
Topic starter  

Parts Needed

Box Dimensions and Cut List

External Box Dimensions - Using 3/4" Material

  • Height: 24"
  • Width: 30"
  • Depth: 18"

This box uses 3/4" material.

Sample Cut List:

  • Front and Rear Baffle: 30" x 24"
  • Top and Bottom: 30" x 16 1/2"
  • Ends: 16 1/2" x 22 1/2"

Ports

Ports. You will need 2 of the Precision ports. If using the precision ports like I uses, you will cut the straight piece to 7" and then glue the flares on. With flared ends, it'll be about 13" in total length. These are designed to be glued on with ABS plumbers glue. However, you can use superglue or any other type of glue. Just make sure their are no air leaks in the port. If you decide to use something else, like PVC pipe a good guesstimate would be about 10" long, However, since I didn't do that, I can't say for sure. I would recommend flaring the ports if you decide to make your own.

Speaker Cutouts and Attachment

I did recess the woofer from on the outside of the box so that it would sit flush. This will be important to do if you decide to turn it into an end table. This allows you to put on around 6" legs. Without this you will want to raise the legs up higher. Each woofer is placed 12" from the bottom and 7 1/2" from the side. The ports will be 5" from the top or bottom and 15" from the sides. You will need to line up the holes correctly so you can bolt the subwoofers together. You can use a centering punch, or what I will do is put the driver in the recess and drill one hole out. Attach a bolt then drill a second hole on the other side. Attach another bolt. The woofer should no longer be able to move, then you can drill all the other holes without worrying about it moving. Just make sure to drill them directly down and not at an angle.

The easiest way to attach the woofers to the front baffle is to use bolts and nuts. I would recommend either locking nuts or double nuts to make sure they do not come loose. You can pick up bolts pretty cheap at your local hardware store. Places like Ace Hardware will sell them by the bolt, which is often times cheaper than buying them in bulk. I used 10-24 bolts that were 1 and 1/2" long. I would not use anything shorter, and it might make it easier for some if they bought 2" long screws. It would help, especially when starting the first nuts. You will need 16 of these bolts and nuts (32 nuts if you decide to double nut it).

Bracing

For the bracing I just use scarp from what I have cut that is the same size as the internal dimensions of the box. These strips I cut around 1.5" wide using that 3/4" scrap. I try to use 12 of these and make sure to glue them together. But you need to make sure you keep plenty of room to remove and install the subwoofers. Make sure they do not go over the ports or where the ports will be. I would wait to glue these in, until after the port were installed. For bracing you will want the following 1.5" strips cut.

  • 4 - 28.5" long
  • 4 - 22.5" long
  • 4 - 16.5" long

Wiring

Each pair of woofers will be wired parallel out of phase. This allows each woofer to move with each other. AKA when one is going in, the other is going out. On the inside of the box you will now have 4 wires that need to go to the amplifier. These will be wired in series to get to a 4 ohm load. The diagram below shows you how to do it, if you are unfamiliar with this terminology.

I used a terminal cup to pass the wires from the inside of the box to the outside of the box. You can use anything you want including binding posts. One thing to think about though, is making sure your wires will be close to your terminal cup. So when placing the woofers and screwing them down, pay attention to where you'll be attaching those wires on the woofers.

Basic Assembly Directions

There really is no right or wrong way to do this, but here is what I find the easiest. I glue all the sides on accept the baffle opposite of the woofers (I'll refer to this as the rear baffle). I'll then paint the front baffle where the woofers will be going. Once that is dry I will attach the ports. I'll also mark the height of the subwoofer on the inside of the box. I want to move on to bracing. With bracing there are a few things to keep in mind. You want to leave room for you to be able to remove the subwoofers if you ever need to. So you do not want your bracing in a way that will impede that. You'll want it outside too woofers or at least give you enough room you can remove it if you need to.

I typically glue in around 12 braces. Two going to each side. Glue these to each panel of the box and to each other. This will help the sides flexing and resonating. Keep in mind, you will not glue 4 of the braces to the rear baffle, since it still is not installed. Do not install these over the ports or in the way of your amplifier or subwoofers.

Once that is finished, I would install the drivers, make sure these are tight and secure. you can now wire these and install the terminal cups. Once that is complete you can glue on the rear baffle. I would glue this facing down, that way no glue will drip on to your woofers, ports or terminal cups. Once that is dry do your finish work and hook it up to the amplifier.

https://www.youtube.com/123toid


Quote

Newegg

Share:
%d bloggers like this: