Home Forums DIY Speakers and Subwoofers Cube Cubed lives again

  • 123toid

    Administrator
    February 20, 2020 at 3:40 am

    are absolutely correct, in the klipsch will be much more powerful.  It is a really fun sub for the price, but there are definitely better out there, especially if you pay a little more.  What is the saying, “There is no replacement for displacement.”  

    I am glad to see it alive again.  It really was a fun little build.  You may want to check for air leaks around the passive radiators.  From removing them and reinstalling them, they may have gotten some leaks. 

     

    Now you can have subs everywhere. 😀 

  • imcokeman

    Member
    February 20, 2020 at 9:50 pm

    I tend to think forced induction is the replacement for displacement, you’ve been in a 2.5 liter car of mine right?  It would be cool if passive radiators worked like forced induction!

    I should definitely check it for leaks, and see about a 30hz filter and it could be a seat for the outdoor movie nights.  Upholstered subwoofer ottoman.

     

  • 123toid

    Administrator
    February 22, 2020 at 4:38 am

    @imcokeman

    Haha, I laughed immediately when you said that.  An outdoor ottoman would be pretty sweet.

     

  • imcokeman

    Member
    February 24, 2020 at 1:16 am

    @123toid is there a way to make a line level 30hz crossover without spending $30 on 2 of those rca ones?

     

  • tvor-ceasar

    Moderator
    February 24, 2020 at 6:48 pm

    I take it you want that for line in and line out levels, and to be high pass (cut the frequencies under 30 Hz).

    This can be done with RC circuits, either passive or active, depends on what you are most comfortable.

    I’m out at the moment, and then have to finish work, but if you get back a little later, I can try to find / come up with something suitable.

  • imcokeman

    Member
    February 24, 2020 at 11:08 pm

    I think anything other than that Dolby Amaze test sound track is fine on it, the Bass lines and thunder in some other movies can come in clear even when loud enough to be higher volume than the rest of the track.  I think based on that excursion chart in Toid’s other thread it’s just that the amaze trailer goes WAY low hz for feel the rumble at HIGH volume and really tests the sub past it’s peak.  

    Seems not to be leaking as pushing on one radiator pushes out other and driver and it stays.

    I probably don’t “need” the 30hz filters for typical movie scenes from what I’m seeing, but if I’m testing, I’m gonna test it hard =)  Although it would be a good way for me to test an easier crossover/filter build I’m thinking too.

    It does definitely sound clean though and I love that!  

  • 123toid

    Administrator
    February 25, 2020 at 4:07 am

    @imcokeman

    I’ve never made one, but what you’re referring to is a passive line level crossover. There’s a lot of calculators online to figure out how to build one. DF mod that was referred to is a passive line level crossover just built into an RCA.

     

  • imcokeman

    Member
    February 25, 2020 at 1:22 pm

    @123toid

    If I did my calculations right i need 510nf capacitor in series on the positive line for 30hz high pass based on a 10.4k input impedence listed for the SA100. Would that be split to 5.2k ohms if I put it before the Y though?  (coming from LFE mono sub signal is split at Y to feed L and R on sub amp) Then it would be 1 microfarad

    I’m using this site for the info https://www.t-linespeakers.org/tech/filters/passiveHLxo.html :

     

  • 123toid

    Administrator
    February 26, 2020 at 6:33 am

    @imcokeman

     

    This is not my expertise, but I don’t see why it would split.  The splitter sends two identical signals, not half the signal.

     

  • imcokeman

    Member
    February 26, 2020 at 9:30 pm

    Looking at the resistance from the rca before the splitter to the amp it looks like it’s in the 11k range with it off so I’ll go with the 510nf value.  Now where is a good place to get tiny caps for line level? I might as well get a few and then I could parallel them if I was off anyway. I’d like to put it in the rca connector and just have like red tape on it to remind me that’s my “subsonic” filter cable =) 

  • 123toid

    Administrator
    February 28, 2020 at 2:44 am
  • tvor-ceasar

    Moderator
    February 28, 2020 at 5:42 pm

    You could always look at Mouser, Digikey, Jameco, or Newark as well. They are all well respected parts supply houses.